Category: ‘Mechanical’
Brinell hardness is determined by forcing a hard steel or carbide sphere of a specified diameter under a specified load into the surface of a material and measuring the diameter of the indentation left after the test.The Brinell ... Read More...
The Rockwell Hardness test is a hardness measurement based on the net increase in depth of impression as a load is applied. Hardness numbers have no units and are commonly given in the R, L, M, E and K scales. The higher the numb... Read More...
There are three types of tests used with accuracy by the metals industry; they are the Brinell hardness test, the Rockwell hardness test, and the Vickers hardness test. Since the definitions of metallurgic ultimate strength and h... Read More...
Hardness measurement can be defined as macro-, micro- or nano- scale according to the forces applied and displacements obtained.
Measurement of the macro-hardness of materials is a quick and simple method of obtaining mechanical... Read More...
Hardness is a characteristic of a material, not a fundamental physical property. It is defined as the resistance to indentation, and it is determined by measuring the permanent depth of the indentation. More simply put, when usin... Read More...
Ensure the mechanical properties of steel end-use of steel properties (mechanical properties) is an important indicator, it depends on the chemical composition and heat treatment of steel system. In the steel standard, according... Read More...
ASTM Specifications
Pipe Smls
Pipe Welded
Tube Smls
Tube Welded
Sheet/Plate
Bar
A790
A790
A789
A789
A240
A276
Mechanical Properties
Specified Tensile Properties ASTM A240
Cold Rolled Plate and ... Read More...
Nominal Composition - wt. %
C
Fe
H
N
O
Ti
0.10 max
0.30 max
0.015 max
0.05 max
0.35 max
rem
Mechanical Properties
Density lb/in3 (g/cm3)
0.163 (4.51)
Metallurgical Condition
1,300 ?F a... Read More...
Nominal Composition - wt. %
C
Fe
H
N
O
Ti
0.10 max
0.30 max
0.015 max
0.03 max
0.25 max
rem
Mechanical Properties
Density lb/in3 (g/cm3)
0.163 (4.51)
Metallurgical Condition
1,300 ?F ann... Read More...
Features of 13-8PH Maraging Stainless Steel Alloy
The 13-8PH alloy is a martensitic, precipitation hardening (maraging) stainless steel
13-8PH Maraging Stainless Steel Alloy Industry Standard
The 13-8PH alloy complies wit... Read More...
304 | 304L | 304H | 316/316L | 316Ti | 317L | 321/321H | 309S | 310S | 347/347H | S32205/S31803 | S32304 | S32750 | S32760 | 904L | 405 | 410 | ... Read More...
Grade
Position of samples1)
Min. total elongation [%]
L0 = 80 mm
L0 = 5,65 √S0
1,5 < e2) ≤ 2
2 < e2) ≤ 2,5
2,5 < e2) < 3
3 ≤ e2) ≤ 25
S235JR
l/t
19/17
20/18
21/... Read More...
Grade
Yield strength
Tensile strength
Min. notch impact energy2)
Temperature
MPa
MPa
J
°C
e3) ≤ 16
e3) > 16
e3) < 3
e3) ≥ 3
S235JR
≥ 235
≥ 225
360 - 510
360 - 510
2... Read More...
The pressing and deep drawing operations are based on shaping sheet metal by plastic deformation. The deformation is achieved by forcing the sheet metal into a formed female die using a male shaped punch. For the pressing oper... Read More...
Notes:
The values shown are for general guidance only for detailed values refer to standards, and supplier literature..
The mechanical property ranges from minimum (No temper- annealed) to maximum (Full temper)
Unalloye... Read More...
Copper is an important engineering material since it is widely used in its pure state and also in alloys with other metals. In its pure state it is the most important material in the electrical industry. It has high electrica... Read More...